Difference between revisions of "Translations:Slicer Voreinstellungen/13/en"

From 3Dator Wiki
Jump to: navigation, search
(Die Seite wurde neu angelegt: „{| class="wikitable" !Preferences !Value |- |Print volume X |180mm |- |Print volumeY |170mm |- |Print volumeZ |260mm |- |Nozzle size |0.5 mm (keep in mind to u…“)
 
Line 58: Line 58:
 
M117 Printing...;Put printing message on LCD screen
 
M117 Printing...;Put printing message on LCD screen
 
M150 R255 U255 B255 P4 ;Change LED Color to white
 
M150 R255 U255 B255 P4 ;Change LED Color to white
 +
;M408 ;enable filament sensor
 
</pre>
 
</pre>
 
|-
 
|-
Line 69: Line 70:
 
M84                        ;steppers off
 
M84                        ;steppers off
 
G90                        ;absolute positioning
 
G90                        ;absolute positioning
 +
;M409 ;disable filament sensor
 
</pre>
 
</pre>
 
|-
 
|-
 
|}
 
|}

Revision as of 08:42, 30 July 2017

Information about message (contribute)
This message has no documentation. If you know where or how this message is used, you can help other translators by adding documentation to this message.
Message definition (Slicer Voreinstellungen)
{| class="wikitable"
!Einstellung
!Wert
|-
|Druckraum X
|180mm
|-
|Druckraum Y
|170mm
|-
|Druckraum Z
|260mm
|-
|Düsen Durchmesser
|0.5 mm (nach jedem Wechsel der Düse muss dieser Wert aktualisiert werden!)
|-
|Heizbett
|Ja
|-
|Filament Durchmesser
|1,75mm
|-
|Kühlung
|min: 30%; max:70%
|-
|Z-Hop
|0,5mm
|-
|retract speed
|120mm/sec
|-
|retract distance
|5mm
|-
|infill prints after perimeter
|Yes
|-
|start gcode
|<pre>;Sliced at: {day} {date} {time}
G21                    ;metric values
G90                    ;absolute positioning
M82                    ;set extruder to absolute mode
M107                    ;start with the fan off
G28                    ;home all axis
G29                    ;Auto Level
G1 Z0.6 F6000          ;move the Nozzle near the Bed
G92 E0                  ;zero the extruded length
G1 Y0                   
G1 X10 E30 F500        ;printing a Line from right to left
G92 E0                  ;zero the extruded length again
G1 Z2
G1 F6000
M117 Printing...        ;Put printing message on LCD screen
M150 R255 U255 B255 P4  ;Change LED Color to white
;M408                  ;enable filament sensor
</pre>
|-
|end gcode
|<pre>
M104 S0                ;extruder heater off
M140 S0                ;heated bed heater off
G91                    ;relative positioning
G1 E-1 F300            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
G1 Z+0.5 E-5            ;move Z up a bit and retract filament even more
G28                    ;home all axis
M84                    ;steppers off
G90                    ;absolute positioning
;M409                  ;disable filament sensor
</pre>
|-
|}
Translation{| class="wikitable"
!Preferences
!Value
|-
|Print volume X
|180mm
|-
|Print volumeY
|170mm
|-
|Print volumeZ
|260mm
|-
|Nozzle size
|0.5 mm (keep in mind to update that value if you change the nozzle!)
|-
|Heated bed
|Yes
|-
|Filament diameter
|1,75mm
|-
|cooling
|min: 30%; max:70%
|-
|Z-hop
|0,5mm
|-
|retract speed
|120mm/sec
|-
|retract distance
|5mm
|-
|infill prints after perimeter
|Yes
|-
|start gcode
|<pre>;Sliced at: {day} {date} {time}
M104 S{print_temperature} ;set temperatures
M140 S{print_bed_temperature}
M109 S{print_temperature} ;wait for temperatures
M190 S{print_bed_temperature}
G21  ;metric values
G90  ;absolute positioning
M82  ;set extruder to absolute mode
M107  ;start with the fan off
G28 Z0  ;move Z to min endstops
G28 X0 Y0  ;move X/Y to min endstops
G29  ;Auto Level
G1 Z0.6 F{travel_speed} ;move the Nozzle near the Bed
G92 E0
G1 Y0  ;zero the extruded length
G1 X10 E30 F500  ;printing a Line from right to left
G92 E0  ;zero the extruded length again
G1 Z2
G1 F{travel_speed}
M117 Printing...;Put printing message on LCD screen
M150 R255 U255 B255 P4 ;Change LED Color to white
;M408 ;enable filament sensor
</pre>
|-
|end gcode
|<pre>M104 S0                    ;extruder heater off
M140 S0                    ;heated bed heater off (if you have it)
G91                                    ;relative positioning
G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
G28                          ;move X/Y to min endstops, so the head is out of the way
M84                        ;steppers off
G90                        ;absolute positioning
;M409 ;disable filament sensor
</pre>
|-
|}
Preferences Value
Print volume X 180mm
Print volumeY 170mm
Print volumeZ 260mm
Nozzle size 0.5 mm (keep in mind to update that value if you change the nozzle!)
Heated bed Yes
Filament diameter 1,75mm
cooling min: 30%; max:70%
Z-hop 0,5mm
retract speed 120mm/sec
retract distance 5mm
infill prints after perimeter Yes
start gcode
;Sliced at: {day} {date} {time}
M104 S{print_temperature} ;set temperatures
M140 S{print_bed_temperature}
M109 S{print_temperature} ;wait for temperatures
M190 S{print_bed_temperature}
G21  ;metric values
G90  ;absolute positioning
M82  ;set extruder to absolute mode
M107  ;start with the fan off
G28 Z0  ;move Z to min endstops
G28 X0 Y0  ;move X/Y to min endstops
G29  ;Auto Level
G1 Z0.6 F{travel_speed} ;move the Nozzle near the Bed
G92 E0
G1 Y0  ;zero the extruded length
G1 X10 E30 F500  ;printing a Line from right to left
G92 E0  ;zero the extruded length again
G1 Z2
G1 F{travel_speed}
M117 Printing...;Put printing message on LCD screen
M150 R255 U255 B255 P4 ;Change LED Color to white
;M408 ;enable filament sensor
end gcode
M104 S0                     ;extruder heater off
M140 S0                     ;heated bed heater off (if you have it)
G91                                    ;relative positioning
G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
G28                          ;move X/Y to min endstops, so the head is out of the way
M84                         ;steppers off
G90                         ;absolute positioning
;M409 ;disable filament sensor